7-loops Stainless Steel Manifold

$237,30

7 loops circuits Stainless Steel Manifold for Hydronic Radiant floor Heating system

Save on the purchase of several units (possibility of combining different models to reach the required quantity)

Buy in quantity and save

Buy 1 pieces
$237,30
Total:
$237,30
Buy 10 pieces and save 10%
$237,30
$213,57
Total:
Buy 20+ pieces and save 15%
$237,30
$201,71
Total:
x

Part #: N/A SKU: MAN-100012-07 Categories: ,

Manifold Ecosolaris pour plancher radiant et chauffant hydronique à l'eau chaude et eau glycol

Ecosolaris Manifolds

The Ecosolaris stainless steel manifolds have been designed with durability, performance, and ease of control in mind. They provide a uniform temperature distribution and facilitate troubleshooting by being equipped with multiple indicators.

  1. Thermometers (supply and return side)
  2. Flowmeters
  3. Air vent (supply and return side)
  4. 1/2″ PEX fittings included (can be optionally replaced with 3/4″, “3/8″, or 5/8” PEX fittings
  5. 1″ FNPT isolation ball valves (supply and return side)
  6. Balancing valve on each loop (replaceable by actuators)
  7. Wall mounting bracket
  8. Drain valves (supply and return side)

Notes: manifolds are available for systems from 2 loops to 12 loops

Shop all our Manifolds

Thermometers

Our namifolds are equipped with 2 thermometers. They are positionned on the return and the supply manifolds. They allow to measure the water temperature coming out from the manifold and moving through the various floor loops and compare it with the water temperature returning to the manifold. The delta (the difference between the hot water leavng the manifold and the cooler water returning to the boiler) is an indication how well your system is operating.

Isolation ball valves

These valves are used to shut-off the water circulation in the supply and return lines. Standard ball valves (red and blue) are used, offering a turn handle. Standard ball valve has one end with a union-type connection to be attached to the manifold. The other end is a 1 inch NTP female inlet.

Flowmeters

There devices are scaled-readers allowing to monitor the volume of water flowing through the radiant manifold’s outlets. Flowmeters are used to balance the flow of water or glycol in the various circuits. The visible part of a flowmeter is an engineered plastic graduated cylinder. You will see a flowmeter on each manifold port. Inside the cylinder a float indicates the water flow rate in the specific PEX loop connected to the manifold port. Water flow rate is graduated in Gallons per minute (GPM) and Liter per minute (L/min). Although non-essential, a manifold without flowmeters makes it very difficult to balance water flow in the various circuits of the system and to diagnose heating problem.

Drain Valves

Drain valves are used to drain the radiant heating system, during maintenance or repairs. These valves allow an easier purge and fill of the system. These valves, combined with the balancing valves, allow the system to be filled, circuit by circuit, when it is put into service, by evacuating as much air as possible from the system.

Air Vents

Air vents are used to eliminate air accumulated inside the circuits. This component is essential on radiant heating manifolds. The air vents will automatically bleed the air, as it accumulates.  For better evacuation, our manifolds are equipped with 2 air vents (one on the fsupply side and one on the return side) which must always be installed head up. Then, the air will accumulate by gravity in the manifold and will become available for bleeding.

Balancing valves

These valves allow to manually regulate the water flow inside the manifold. Each manifold outlet has its own valve, allowing increasing or reducing the flow through the loop. These adjustments are done to adjust the flow of hot water in the individual loops, consequently impacting on the temperature of that specific zone. These outlets adjustments have an impact on the entire heat flow of the manifold and its distribution, by modifying heat distribution in all the loops.

Mounting position of Ecosolaris hydronic radiant floor manifold
Weight6,35029318 kg
Dimensions24 × 14,5 × 5 cm

You may also like…